Abstract
This paper presents an original method to inversely identify the Johnson–Cook model constants (J-C constants) of ultra-fine-grained titanium (UFG Ti) based on a chip formation model and an iterative gradient search method using Kalman filter algorithm. UFG Ti is increasingly finding usefulness in lightweight engineering applications and medical implant filed because of its sufficient mechanical strength, high manufacturability, and high biocompatibility. Johnson–Cook model is one of the constitutive models widely used in analytical modeling of machining force, temperature, and residual stress because it is effective, simple, and easy to use. Currently, the J-C constants of UFG Ti are unavailable and yet an effective identification methodology based upon machining data is not readily available. In this work, multiple cutting tests were conducted under different cutting conditions, in which machining forces were experimentally measured using a piezoelectric dynamometer. The machining forces were also predicted using the chip formation model with inputs of cutting conditions, workpiece material properties, and a set of given model constants. An iterative gradient search method was enforced to find the J-C constants when the difference between predicted forces and experimental forces reached an acceptable low value. To validate the identified J-C constants, machining forces were predicted using the identified J-C constants under different cutting conditions and then compared to the corresponding experimental forces. Close agreements were observed between predicted forces and experimental forces. Considering the simple orthogonal cutting tests, reliable and easily measurable machining forces, and efficient iterative gradient search method, the proposed method has less experimental complexity and high computational efficiency.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Brunette DM, Tengvall P, Textor M, Thomsen P (2001) Titanium in medicine: material science, surface science, engineering, biological responses and medical applications. Springer Verlag Berlin Heidelberg, New York
Stolyarov VV, Zhu YT, Alexandrov IV, Lowe TC, Valiev RZ (2001) Influence of ECAP routes on the microstructure and properties of pure Ti. Mater Sci Eng A 299(1–2):59–67
Valiev RZ, Langdon TG (2006) Principles of equal-channel angular pressing as a processing tool for grain refinement. Prog Mater Sci 51(7):881–981
Majzoobi GH, Freshteh-Saniee F, Khosroshahi SFZ, Mohammadloo HB (2010) Determination of materials parameters under dynamic loading. Part I: experiments and simulations. Comput Mater Sci 49(2):192–200
Dorogoy A, Rittel D (2009) Determination of the Johnson–Cook material parameters using the SCS specimen. Exp Mech 49(6):881–885
Khan AS, Suh YS, Kazmi R (2004) Quasi-static and dynamic loading responses and constitutive modeling of titanium alloys. Int J Plast 20(12):2233–2248
Milani AS, Dabboussi W, Nemes JA, Abeyaratne RC (2009) An improved multi-objective identification of Johnson–Cook material parameters. Int J Impact Eng 36(2):294–302
Özel T, Karpat Y (2007) Identification of constitutive material model parameters for high-strain rate metal cutting conditions using evolutionary computational algorithms. Mater Manuf Process 22(5):659–667
Kolsky H (1949) An investigation of the mechanical properties of materials at very high rates of loading. Proc Phys Soc. Section B 62(11):676–700
Shrot A, Bäker M (2012) Determination of Johnson–Cook parameters from machining simulations. Comput Mater Sci 52(1):298–304
Umbrello D, M’saoubi R, Outeiro JC (2007) The influence of Johnson–Cook material constants on finite element simulation of machining of AISI 316L steel. Int J Mach Tools Manuf 47(3):462–470
Agmell M, Ahadi A, Ståhl JE (2014) Identification of plasticity constants from orthogonal cutting and inverse analysis. Mech Mater 77:43–51
Oxley PL, Welsh MJ (1963) Calculating the shear angle in orthogonal metal cutting from fundamental stress-strain-strain rate properties of the work material. In: Proceedings of the fourth international conference on machine tool design and research conference, Manchester, England, pp 73–86
Naik P, Naik A (2015) Determination of flow stress constants by Oxley‘s theory. Int J Latest Technol Eng, Manage Appl Sci 4(10):110–116
Özel T, Zeren E (2006) A methodology to determine work material flow stress and tool-chip interfacial friction properties by using analysis of machining. J Manuf Sci Eng 128(1):119–129
Tounsi N, Vincenti J, Otho A, Elbestawi MA (2002) From the basic mechanics of orthogonal metal cutting toward the identification of the constitutive equation. Int J Mach Tools Manuf 42(12):1373–1383
Ning J, Liang SY (2018) Model-driven determination of Johnson-Cook material constants using temperature and force measurements. Int J Adv Manuf Technol 97(1–4):1053–1060
Oxley PLB (1989) The mechanics of machining: an analytical approach to assessing machinability. Ellis Horwood Ltd., England
Adibi-Sedeh AH, Madhavan V, Bahr B (2003) Extension of Oxley’s analysis of machining to use different material models. J Manuf Sci Eng 125(4):656–666
Industrial Administration and Engineering Production Group Applied Mechanics Group, Boothroyd G (1963) Temperatures in orthogonal metal cutting. Proc Inst Mech Eng 177(1):789–810
Kalman RE, Bucy RS (1961) New results in linear filtering and prediction theory. J Basic Eng 83(1):95–108
Funding
The study received financial support from the US National Science Foundation.
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
About this article
Cite this article
Ning, J., Nguyen, V., Huang, Y. et al. Inverse determination of Johnson–Cook model constants of ultra-fine-grained titanium based on chip formation model and iterative gradient search. Int J Adv Manuf Technol 99, 1131–1140 (2018). https://doi.org/10.1007/s00170-018-2508-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2508-6